Load data for 9 mm Browning Court (.380 ACP) + .356 | 95gr | H&N RN HS

Recommended Powder(s): Rottweil P 801

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.356 \| 95gr \| H&N RN HS
Bullet Weight:	95gr \| 6.2g
Bullet Diameter:	0.356" \| 9.04mm
Bullet Length:	0.496" \| 12.6mm
Caliber:	9 mm Browning Court (.380 ACP) load data
Case Length (l3):	0.681" \| 17.3mm
Cartridge Length (C.O.L.):	0.969" \| 24.6mm
Seated Depth:	0.208" \| 5.3mm
Shank Seated Depth:	0.188" \| 4.8mm
Case Capacity:	12.2 Grains of Water \| 0.79 cm³
Primer Size:	Small Pistol (SP)
Max. allowed Pressure:	19580 psi \| 1350 bar
LID:	LID_B7439_C1213
Last updated:	2025-01-01

Load data for 70 loads in caliber 9 mm Browning Court (.380 ACP) with .356 | 95gr | H&N RN HS bullet and 35 powders such as Rottweil P 801. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 70N	<<locked>>	76%	16462	84%	**89	95%
ADI APS 350	<<locked>>	69%	17463	89%	**8	100%
ADI APS 450	<<locked>>	72%	17550	90%	**4	100%
ADI AS 30	<<locked>>	77%	15911	81%	**01	100%
ADI AS 50N	<<locked>>	77%	16172	83%	**30	98%
Accurate Solo 1000	<<locked>>	76%	16795	86%	**14	99%
Accurate Solo 1250	<<locked>>	90%	17448	89%	**73	94%
[Alliant BULLSEYE]*	<<locked>>	74%	16244	83%	**53	86%
[Alliant UNIQUE]*	<<locked>>	91%	16056	82%	**86	86%
Baschieri & Pellagri 100	<<locked>>	82%	16694	85%	**27	97%
Hodgdon Clays	<<locked>>	69%	17405	89%	**1	100%
Hodgdon Universal	<<locked>>	84%	16462	84%	**89	95%
Lovex S011	<<locked>>	69%	17463	89%	**30	95%
[Lovex S020]*	<<locked>>	84%	16781	86%	**79	89%
Maxam CSB 1	<<locked>>	91%	16128	82%	**40	93%
Maxam CSB 2	<<locked>>	96%	15853	81%	**22	98%
Maxam CSB 3	<<locked>>	86%	17013	87%	**60	98%
Maxam CSB 4	<<locked>>	79%	16012	82%	**27	99%
Maxam CSB 5	<<locked>>	73%	15983	82%	**10	100%
[Ramshot Silhouette]*	<<locked>>	76%	17303	88%	**86	83%
ReloadSwiss RS 12	<<locked>>	84%	16099	82%	**25	100%
[ReloadSwiss RS 20]*	<<locked>>	95%	16433	84%	**89	88%
Rottweil P 801 👍	<<locked>>	77%	16940	87%	**06	100%
[SNPE Vectan A0]*	<<locked>>	92%	17550	90%	**47	86%
SNPE Vectan BA 9	<<locked>>	81%	17477	89%	**43	91%
SNPE Vectan BA10	<<locked>>	67%	17521	90%	**4	100%
SNPE Vectan BA9 1/2	<<locked>>	83%	16563	85%	**56	93%
[Somchem MP200]*	<<locked>>	83%	16810	86%	**73	84%
[Somchem MS200]*	<<locked>>	86%	16882	86%	**63	88%
Vihtavuori N310	<<locked>>	65%	16375	84%	**04	100%
Vihtavuori N320	<<locked>>	84%	16926	86%	**83	99%
Vihtavuori N32C Tin Star	<<locked>>	94%	10153	52%	**2	100%
Vihtavuori N330	<<locked>>	90%	17535	90%	**25	96%
[Vihtavuori N340]*	<<locked>>	89%	16447	84%	**60	86%
Winchester 231	<<locked>>	68%	16476	84%	**47	95%

Max Load - Barrel Length: 5.50''

Powder	Charge	FR	MaxP	%	V(0)	z
[ADI AP 70N]*²	<<locked>>	59%	9877	50%	**2	86%
[ADI APS 350]²	<<locked>>	59%	13271	68%	**6	100%
ADI APS 450	<<locked>>	63%	13721	70%	**6	100%
[ADI AS 30]²	<<locked>>	59%	9529	49%	**0	97%
ADI AS 50N	<<locked>>	60%	10153	52%	**3	92%
[Accurate Solo 1000]²	<<locked>>	59%	10457	53%	**3	93%
[Accurate Solo 1250]*	<<locked>>	67%	8949	46%	**0	82%
[Alliant BULLSEYE]*	<<locked>>	64%	11879	61%	**8	80%
[Alliant UNIQUE]*	<<locked>>	80%	12198	62%	**1	80%
[Baschieri & Pellagri 100]*	<<locked>>	63%	9355	48%	**7	89%
[Hodgdon Clays]²	<<locked>>	59%	13285	68%	**6	100%
[Hodgdon Universal]*	<<locked>>	62%	8688	44%	**6	83%
Lovex S011	<<locked>>	62%	14054	72%	**1	92%
[Lovex S020]*	<<locked>>	71%	10950	56%	**2	81%
[Maxam CSB 1]*	<<locked>>	67%	8470	43%	**0	81%
[Maxam CSB 2]*	<<locked>>	62%	5889	30%	**1	80%
[Maxam CSB 3]*	<<locked>>	61%	8557	44%	**4	87%
Maxam CSB 4	<<locked>>	62%	9964	51%	**0	93%
Maxam CSB 5	<<locked>>	60%	10849	55%	**3	100%
[Ramshot Silhouette]*	<<locked>>	70%	14518	74%	**17	80%
ReloadSwiss RS 12	<<locked>>	60%	7063	36%	**0	90%
[ReloadSwiss RS 20]*	<<locked>>	84%	12604	64%	**8	82%
Rottweil P 801	<<locked>>	60%	9689	49%	**9	97%
[SNPE Vectan A0]*	<<locked>>	81%	13431	69%	**2	81%
[SNPE Vectan BA 9]*	<<locked>>	61%	9761	50%	**7	80%
SNPE Vectan BA10	<<locked>>	63%	15635	80%	**8	100%
[SNPE Vectan BA9 1/2]*	<<locked>>	62%	8862	45%	**3	81%
[Somchem MP200]*	<<locked>>	77%	13924	71%	**7	81%
[Somchem MS200]*	<<locked>>	72%	11560	59%	**2	80%
Vihtavuori N310	<<locked>>	61%	14344	73%	**1	100%
Vihtavuori N320	<<locked>>	60%	8224	42%	**7	91%
Vihtavuori N32C Tin Star	<<locked>>	66%	4931	25%	**6	91%
[Vihtavuori N330]*	<<locked>>	65%	8354	43%	**7	82%
[Vihtavuori N340]*	<<locked>>	78%	12154	62%	**5	80%
Winchester 231	<<locked>>	62%	13402	68%	**8	92%

Start Load - Barrel Length: 5.50''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data